TEL:(86) 511 8443 6131 E-MAIL:sales@cmpter.com
  
Home | Products | Products Finder | About Us | Resource Center | Contact Us
  RF Coaxial Connectors
  1.85mm Connector
  2.4mm Connector
  2.92mm Connector
  7/16 connector
  BNC/RPBNC Connector
  MCX Connector
  MMCX Connector
  N-Type Connector
  SMA & RPSMA Connector
  SMP Connector
  SMB Connector
  SSMA Connector
  TNC & RPTNC Connector
  TNCA Connector
  RF Coaxial Adapters
  RF Cable Assembly
  RF Coaxial Termination
  RF Surge Arrestor
  RF Coaxial Cable
  Accessories
  Tools
Home > Products > Glass Bead Install Tools
Glass Bead Install Tools
  
Concentricity is very critical for glass bead install, if concentricity is not good will not only influence the
performance, but also easy to damage the connector. So take the glass bead install tools that will be a
very good solution to solve this problem.
1. Install Tools for flange connectors
    1)Usage:Include position tool and centring tool, position tool is used for positioning the flange
           concentric position, centring tool is used for guarantee the concentric of the glass bead.
           Step 1: Fit the glass bead into the shell, wedge the solder into the welding gap.
           Setp 2: Choose the positioning tool which the hole spacing is same like the connector flange,
                        and screw tightening.
           Step 3: Screw the centring tool into the position tool, glass bead pin slide into the center hole,
                        then screw tightening the centring tool.
           Setp 4: Vertical heating the shell and install tools together.
           Setp 5: After cooling, remove the centring tool and the positioning tool.
 
       2)Tools Model
           a. Positioning tool
               Positioning tools are all two hole structure, when install four hole flange, adopting diagonal
               installation.
 

P/N

GT122

GT102

GT890

GT086

Hole spacing L1

12.2mm/.480''

10.2mm/.400''

8.9mm/.350''

8.6mm/.340''

Hole spacing L2

8.6mm/.339''

6.35mm/.250''

NA

NA

           b. Centring tool
 

P/N

GCT09

GCT12

GCT15

GCT18

GCT20

Centring Dia. 

0.23mm/.009''

0.30mm/.012'

0.38mm/.015''

0.46mm/.018''

0.51mm/.020''

   

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

  
2. Install Tool for threaded in connectors
           1) Usage: Only need a centring tool to centring the glass bead.
               Step 1: Fit the glass bead into the shell, wedge the solder into the welding gap.
               Step 2: Screw the centring tool into the mounting hole, glass bead pin slide into the center
             hole, then screw tightening the centring tool.
               Step 3: Vertical heating the shell and the centring tool together.
               Setp 4: After cooling, remove the centring tool.
           2) Tools Mode

 

P/N

GCK09

GCK12

GCK15

GCK18

GCK20

   Centring Dia.  

0.23mm/.009''

0.30mm/.012'

0.38mm/.015''

0.46mm/.018''

0.51mm/.020''

Glass Bead Install Tools Instruction [PDF]

 

 

  
  Recommended Products:
Home | About us | Contact us | Disclaimer | Privacy Policy | Site Map | Cmpter Electronics Co., Ltd. sales@cmpter.com
Tel:(86)511 8443 6131 Fax:(86)511 8717 7136
Copyright © Cmpter Electronics 2013